Ambit-Ubee: Overview

Discus and support Ambit-Ubee: Overview in XboX Networking Hardware to solve the problem; Ambit-Ubee (Modems/Gateways): Overview Ubee DDW365 Login Information Default Gateway - 192.168.0.1 Username - user Password - user This portion... Discussion in 'XboX Networking Hardware' started by XB1R Hades, Aug 15, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Ambit-Ubee: Overview


    Ambit-Ubee (Modems/Gateways): Overview
    Ubee DDW365

    Login Information

    • Default Gateway - 192.168.0.1
    • Username - user
    • Password - user

    This portion of the guide is written for the older version of Ubee firmware that is more commonly found on these devices. This firmware tends to have the Ubee logo featured in the center on the top of the screen.
    the newer firmware guide is listed below this guide.


    How to Find SSID(Network Name)

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Click "Wireless" across the top.
    6. On the left had side click "Primary Network".
    7. The SSID is on this page labeled Network Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Primary Network from the menu on the left.
    7. Select the check box that says show characters.
    8. Verify the password displayed.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Primary Network from the menu on the left.
    7. Enable the desired security type. (WPA-PSK, WPA2-PSK)
    8. To turn off the security select Disable for all the security types.
    How to Change Wireless Mode

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Radio from the menu on the left.
    7. Select G-Only mode from 802.11 n-Mode drop down menu.
    8. Select Apply.


    How to Change Wireless Band (Width)

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Radio from the menu on the left.
    7. Select 20 Mhz from the Bandwidth drop down.
    8. Select Apply.
    How to Change Wireless Channel

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Radio from the menu on the left.
    7. From the Control Channel drop down select the desired wireless channel. (Channels 1,3,9,11)
    8. Select Apply.


    DMZ

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select DMZ Host from the menu on the left.
    7. Enter IP address of the Xbox in the DMZ address box.
    8. Select Apply.
    Disable DMZ

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select DMZ Host from the menu on the left.
    7. Enter a 0 in the DMZ address box. (if 0 is not allowed use 1)
    8. Select Apply.


    DHCP Reservation

    (Note: You MUST force release of the IP address on the DHCP page First)

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu at the top.
    6. Select "Gateway" across the top.
    7. Select "Static Lease" on the left.
    8. Enter in the Mac and IP addresses for the Xbox.
    9. Select the Enable Check box to the right.
    10. Select Apply.


    Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select Port Forwarding from the menu on the left.
    7. Enter IP address of the Xbox.
    8. Enter the internal Port Number 3074.
    9. Enter the Ext. Start Port Number 3074.
    10. Enter the Ext. End Port Number 3074.
    11. Set the protocol to both.
    12. Select Apply.
    Disable Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select Port Forwarding from the menu on the left.
    7. Uncheck the Enable box of the ports you want to remove.
    8. Select Apply.


    Firewall

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. From the menu across the top select Firewall.
    6. Select Content Filter from the menu on the left.
    7. Un-check IP-Flood detection and Firewall Protection.
    8. Select Apply.


    Restore Defaults

    Through firmware

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Tools from the menu at the top.
    6. Select Yes for both Restore Defaults and Reset The System.
    7. Select Apply.
    Through Hardware

    1. Locate the reset button on the back of the device (it is labeled "Reset").
    2. Hold the reset button for 30 seconds.






    UPnP

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the top menu.
    6. Select Options under the advanced section of the menu on the left.
    7. Toggle the UPnP option and select apply.


    Updating Firmware

    *Firmware updates are installed automatically by the Internet Service Provider.*

    How to Find Firmware Version

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Before logging in the firmware version is located here labeled Software Version.


    Bridging Guide

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Enter http://192.168.0.1/TlModeChange.asp
    6. Change the mode to Bridge Mode.
    7. Click the Apply button.


    MAC Filtering

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Click "Gateway" across the top.
    6. On the left had side click "MAC Filtering".
    7. If the Xbox is on this list put a check in the Clear box and select Apply.
    Device Manual

    Click Here

    Multiple Console Support

    Confirmed no



    Known Issues

    This device's firewall settings can cause many online gaming issues with either Xbox model. If you are experiencing online multiplayer issues we recommend disabling IP Flood detection and Firewall Protection in the Firewall section.

    Are you experiencing a live connection error with this device right after setting it up for the first time? We’ve found a long power cycle (unplug the device for 5 minutes then reconnect) or a DMZ setup for your Xbox tends to resolve the issue more
    often than not.

    WPA-PSK 2 passphrases can cause issues with the Xbox One. If you are having trouble connecting wirelessly and you have a WPA2 passkey try switching it to WPA.



    This guide is meant for the newer firmware version for this device where the Ubee logo is featured more in the top left of the main screen.



    Ubee DDW365

    Login Information

    • Default Gateway - 192.168.100.1
    • Username - user
    • Password - user


    How to Find SSID(Network Name)

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Primary Network from the menu on the left.
    6. The SSID is on this page labeled Network Name (SSID).


    How to Find Wireless Passphrase (WPA/WEP)

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Primary Network from the menu on the left.
    6. Select the check box that says show characters or key depending on which type of security is enable.
    7. Verify the password displayed.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Primary Network from the menu on the left.
    6. Enable the desired security type. (WPA-PSK, WPA2-PSK)
    7. To turn off the security select Disable for all the security types.
    How to Change Wireless Mode

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Radio from the menu on the left.
    6. Select G-Only mode from 802.11 n-Mode drop down menu.
    7. Select Apply.
    How to Change Wireless Band (Width)

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Radio from the menu on the left.
    6. Select 20 Mhz from the Bandwidth drop down.
    7. Select Apply.
    How to Change Wireless Channel

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Radio from the menu on the left.
    6. From the Control Channel drop down select the desired wireless channel. (Channels 1,3,9,11) The device should be able to tell you if there is interference on the particular channel you select so try to select a channel where the level is acceptable
      as listed by the device.
    7. Select Apply.


    DMZ

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select DMZ Host from the menu on the left.
    6. Enter IP address of the Xbox in the DMZ address box.
    7. Select Apply.
    Disable DMZ

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select DMZ Host from the menu on the left.
    6. Enter a 0 in the DMZ address box. (if 0 is not allowed use 1)
    7. Select Apply.


    DHCP Reservation

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Basic from the menu at the top.
    5. Select DHCP on the left.
    6. Find your Xbox on the list labeled DHCP Clients and select the select button
    7. This should reserve the current private IP address for your Xbox.


    Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select Forwarding from the menu on the left.
    6. Select Create IPv4
    7. Enter IP address of the Xbox.
    8. For all areas asking for a start port or an end port enter 3074
    9. Set the protocol to both.
    10. Select Save.
    Disable Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select Forwarding from the menu on the left.
    6. Uncheck the Enable box of the ports you want to remove. Or select Remove all.
    7. Select Save.


    Firewall

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. From the menu across the top select Firewall.
    5. Select Basic from the menu on the left.
    6. Set IPv4 Firewall Protection to Low
    7. Check the Optimize for XBOX box.
    8. Select Apply.


    Restore Defaults

    Through firmware

    The firmware walkthrough for restoring factory defaults only removes user changes to the firewall settings and parental control settings. It is advised you do so via the hardware method.

    Through Hardware

    1. Locate the reset button on the back of the device (it is labeled "Reset").
    2. Hold the reset button for 30 seconds.






    UPnP

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the top menu.
    5. Select Options from the menu on the left.
    6. Check or uncheck the UPnP option and select apply.


    Updating Firmware

    *Firmware updates are installed automatically by the Internet Service Provider.*

    How to Find Firmware Version

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Status from the menu at the top.
    5. Select Software from the menu on the left.
    6. Your firmware version will be listed as Software Version.


    Bridging Guide

    *Bridging is not available through the firmware. Please contact your ISP to see if bridging is possible.*

    MAC Filtering

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Click Advanced across the top.
    5. On the left hand side select MAC Filtering
    6. If the Xbox is on this list select it and then select remove MAC Address.


    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Known Issues

    This device's firewall settings can cause many online gaming issues with either Xbox model. If you are experiencing online multiplayer issues we recommend setting IPv4 Firewall Protection to Low to help resolve.

    Are you experiencing a live connection error with this device right after setting it up for the first time? We’ve found a long power cycle (unplug the device for 5 minutes then reconnect) or a DMZ setup for your Xbox tends to resolve the issue more
    often than not.

    WPA-PSK 2 passphrases can cause issues with the Xbox One. If you are having trouble connecting wirelessly and you have a WPA2 passkey try switching it to WPA.



    :)
     
    XB1R Hades, Aug 15, 2014
    #1
  2. XB1R Hades
    XB1R Hades Guest
    Ambit-Ubee: Overview

    Ambit-Ubee (Modems/Gateways): Overview
    Ambit-Ubee U10C019

    Login Information

    • Default Gateway - 192.168.0.1
    • Username - user
    • Password - user

    Wireless Security

    How to Find Wireless Passphrase


    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Primary Network from the menu on the left.
    7. Select the check box that says show characters.
    8. Verify the password displayed.
    How to Change Wireless Security

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Primary Network from the menu on the left.
    7. Enable the desired security type. (WPA-PSK, WPA2-PSK)
    8. To turn off the security select Disable for all the security types.


    DMZ

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select DMZ Host from the menu on the left.
    7. Enter the IP address of the Xbox in the DMZ address box.
    8. Select Apply.
    Disable DMZ

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select DMZ Host from the menu on the left.
    7. Enter a 0 in the DMZ address box. (if 0 is not allowed use 1)
    8. Select Apply.


    DHCP Reservation

    (Note: You MUST force release of the IP address on the DHCP page First)

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu at the top.
    6. Select "Gateway" across the top.
    7. Select "Static Lease" on the left.
    8. Enter in the Mac and IP addresses for the Xbox.
    9. Select the Enable Check box to the right.
    10. Select Apply.


    Port Forwarding

    1. Enter http://192.168.0.1 in the address bar.
    2. Select login from the side menu.
    3. Enter the username and password. (user/user)
    4. Select Gateway from the menu across the top.
    5. Select Port Forwarding from the menu on the left.
    6. Enter IP address of the Xbox.
    7. Enter the internal Port Number 3074.
    8. Enter the Ext. Start Port Number 3074.
    9. Enter the Ext. End Port Number 3074.
    10. Set the protocol to both.
    11. Select Apply.
    Disable Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the menu across the top.
    6. Select Port Forwarding from the menu on the left.
    7. Uncheck the Enable box of the ports you want to remove.
    8. Select Apply.


    Firewall

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. From the menu across the top select Firewall.
    6. Select Content Filter from the menu on the left.
    7. Un-check IP-Flood detection and Firewall Protection.
    8. Select Apply.


    Restore Defaults

    Through firmware

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Tools from the menu at the top.
    6. Select Yes for both Restore Defaults and Reset The System.
    7. Select Apply.
    Through Hardware

    1. Locate the reset button on the back of the device (it is labeled "Reset").
    2. Hold the reset button for 30 seconds.


    Change Wireless Mode

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Radio from the menu on the left.
    7. Select G-Only mode from 802.11 n-Mode drop down menu.
    8. Select Apply.


    Change Wireless Channel

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Wireless from the menu at the top.
    6. Select Radio from the menu on the left.
    7. From the Control Channel drop down select the desired wireless channel. (Channels 1,3,9,11)
    8. Select Apply.


    UPnP

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Gateway from the top menu.
    6. Select Options under the advanced section of the menu on the left.
    7. Toggle the UPnP option and select apply.


    Updating Firmware

    *Firmware updates are installed automatically by the Internet Service Provider.*

    How to Find Firmware Version

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Before logging in the firmware version is located here labeled Software Version.


    Bridging Guide

    *Bridge mode should only be used if you have a router to plug into the device.*

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Select Tools from the top menu.
    6. Select Operation Mode from the menu on the left.
    7. Select Enable to the right of "Bridge mode:".
    8. Click Apply.


    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    How to Find SSID(Network Name)

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Click "Wireless" across the top.
    6. On the left had side click "Primary Network".
    7. The SSID is on this page labeled Network Name (SSID).


    MAC Filter

    1. Open a web browser.
    2. Enter http://192.168.0.1 in the address bar.
    3. Select login from the side menu.
    4. Enter the username and password. (user/user)
    5. Click "Gateway" across the top.
    6. On the left had side click "MAC Filtering".
    7. If the Xbox is on this list put a check in the Clear box and select Apply.


    Known Issues

    This device will give NAT-like issues, random disconnections and in-game errors (such as "Black Ops Servers Unavailable") while IP Flood Detection and Firewall Protection are enabled. Try disabling one or both to resolve the issue.
     
    XB1R Hades, Aug 15, 2014
    #2
  3. XB1R Hades
    XB1R Hades Guest
    Ambit-Ubee: Overview

    Ambit-Ubee (Modems/Gateways): Overview
    Ambit-Ubee DVW3201B



    Login Information

    • Default Gateway - 192.168.100.1
    • Username - user
    • Password - user


    How to Find SSID(Network Name)

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Primary Network from the menu on the left.
    6. The SSID is on this page labeled Network Name (SSID).




    How to Find Wireless Passphrase (WPA/WEP)

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Primary Network from the menu on the left.
    6. Select the check box that says show characters or key depending on which type of security is enable.
    7. Verify the password displayed.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Primary Network from the menu on the left.
    6. Enable the desired security type. (WPA-PSK, WPA2-PSK)
    7. To turn off the security select Disable for all the security types.
    How to Change Wireless Mode

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Radio from the menu on the left.
    6. Select G-Only mode from 802.11 n-Mode drop down menu.
    7. Select Apply.
    How to Change Wireless Band (Width)

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Radio from the menu on the left.
    6. Select 20 Mhz from the Bandwidth drop down.
    7. Select Apply.
    How to Change Wireless Channel

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Wireless from the menu at the top.
    5. Select Radio from the menu on the left.
    6. From the Control Channel drop down select the desired wireless channel. (Channels 1,3,9,11) The device should be able to tell you if there is interference on the particular channel you select so try to select a channel where the level is acceptable
      as listed by the device.
    7. Select Apply.


    DMZ

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select DMZ Host from the menu on the left.
    6. Enter IP address of the Xbox in the DMZ address box.
    7. Select Apply.
    Disable DMZ

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select DMZ Host from the menu on the left.
    6. Enter a 0 in the DMZ address box. (if 0 is not allowed use 1)
    7. Select Apply.


    DHCP Reservation

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Basic from the menu at the top.
    5. Select DHCP on the left.
    6. Find your Xbox on the list labeled DHCP Clients and select the select button
    7. This should reserve the current private IP address for your Xbox.


    Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select Forwarding from the menu on the left.
    6. Select Create IPv4
    7. Enter IP address of the Xbox.
    8. For all areas asking for a start port or an end port enter 3074
    9. Set the protocol to both.
    10. Select Save.
    Disable Port Forwarding

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the menu across the top.
    5. Select Forwarding from the menu on the left.
    6. Uncheck the Enable box of the ports you want to remove. Or select Remove all.
    7. Select Save.


    Firewall

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. From the menu across the top select Firewall.
    5. Select Basic from the menu on the left.
    6. Set IPv4 Firewall Protection to Low
    7. Check the Optimize for XBOX box.
    8. Select Apply.


    Restore Defaults

    Through firmware

    The firmware walkthrough for restoring factory defaults only removes user changes to the firewall settings and parental control settings. It is advised you do so via the hardware method.

    Through Hardware

    1. Locate the reset button on the back of the device (it is labeled "Reset").
    2. Hold the reset button for 30 seconds.
    UPnP

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Advanced from the top menu.
    5. Select Options from the menu on the left.
    6. Check or uncheck the UPnP option and select apply.


    Updating Firmware

    *Firmware updates are installed automatically by the Internet Service Provider.*

    How to Find Firmware Version

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Select Status from the menu at the top.
    5. Select Software from the menu on the left.
    6. Your firmware version will be listed as Software Version.


    Bridging Guide

    *Bridging is not available through the firmware. Please contact your ISP to see if bridging is possible.*

    MAC Filtering

    1. Open a web browser.
    2. Enter http://192.168.100.1 in the address bar.
    3. When prompted enter user for the username and user for the password.
    4. Click Advanced across the top.
    5. On the left hand side select MAC Filtering
    6. If the Xbox is on this list select it and then select remove MAC Address.


    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Known Issues

    This devices firewall settings can cause many online gaming issues with either Xbox model. If you are experiencing online multiplayer issues we recommend setting IPv4 Firewall Protection to Low to help resolve.
     
    XB1R Hades, Aug 15, 2014
    #3
  4. Micaciousness Win User

    Ambit-Ubee: UPnP

    The UPnP option on my router is enabled and it's still not working.
  5. SinlessGuitar66 Win User

    Ambit-Ubee: Firewall

    instructions are wrong, there is no "basic" menu
  6. LitVire Win User

    Ambit-Ubee: UPnP

    instructions not for this device.
  7. Ka7as7rophic Win User

    Ambit-Ubee: DMZ

    thats all u have to and u can play ur games on xbox problem free?
  8. Zeeko4ever Win User

    Ambit-Ubee: Ipv4

    hey did they help you fix this problem I been having the same issue
Thema:

Ambit-Ubee: Overview

Loading...
  1. Ambit-Ubee: Overview - Similar Threads - Ambit Ubee Overview

  2. Ambit-Ubee Ambit-Ubee DDM3500: Quiero cancelar mi suscripcion de xbox live

    in XboX Networking Hardware
    Ambit-Ubee Ambit-Ubee DDM3500: Quiero cancelar mi suscripcion de xbox live: Ambit-Ubee (Modems/Gateways) Ambit-Ubee DDM3500 (Modem): Quiero cancelar mi suscripcion de xbox live Log in here: https://account.microsoft.com/services/ Cancel your membership...
  3. Ambit-Ubee Ambit-Ubee U10C034: Jual Panel Surya yang Murah di Surabaya

    in XboX Networking Hardware
    Ambit-Ubee Ambit-Ubee U10C034: Jual Panel Surya yang Murah di Surabaya: Ambit-Ubee (Modems/Gateways) Ambit-Ubee U10C034: Jual Panel Surya yang Murah di Surabaya The last few times the issue of electricity bills that continue to increase make people worried. Everyone...
  4. Ambit-Ubee Ambit-Ubee DVW3201B: Your Wireless adapter or whatever it is need some fixing! XBOX ...

    in XboX Networking Hardware
    Ambit-Ubee Ambit-Ubee DVW3201B: Your Wireless adapter or whatever it is need some fixing! XBOX ...: Ambit-Ubee (Modems/Gateways) Ambit-Ubee DVW3201B: Your Wireless adapter or whatever it is need some fixing! XBOX EMPLOYEES ONLY. you could make sure all accounts you are using have xbox live...
  5. Ambit-Ubee: how to capture 3d data from kinect

    in XboX Networking Hardware
    Ambit-Ubee: how to capture 3d data from kinect: Ambit-Ubee (Modems/Gateways): how to capture 3d data from kinect how to capture 3d data from kinect (3d using depth information) and how to read them? please give me an example....
  6. Ambit-Ubee: being followed and cheated in all my games by a hacker

    in XboX Networking Hardware
    Ambit-Ubee: being followed and cheated in all my games by a hacker: Ambit-Ubee (Modems/Gateways): being followed and cheated in all my games by a hacker please help me I'm being followed and cheated in all of my games by a hacker i believe he's DDOS me i have...
  7. Ambit-Ubee: being cheated on xbox live

    in XboX Networking Hardware
    Ambit-Ubee: being cheated on xbox live: Ambit-Ubee (Modems/Gateways): being cheated on xbox live i am being cheated in games online by a hacker its been going on for about 4yrs he follows me using multiple gamertag the most recent...
  8. Ambit-Ubee: Error code 8015190e

    in XboX Networking Hardware
    Ambit-Ubee: Error code 8015190e: Ambit-Ubee (Modems/Gateways): Error code 8015190e hopefully this helps bud Having Connection issues? Easy Fix 67215bcc-d3a5-4c40-b2c9-ce0d89f21f4b
  9. Ambit-Ubee: Overview

    in XboX Networking Hardware
    Ambit-Ubee: Overview: Ambit-Ubee (Modems/Gateways): Overview Ambit-Ubee DVW3201B Login Information Default Gateway - 192.168.100.1 Username - user Password - user How to Find SSID(Network Name) Open a...
  10. Ambit-Ubee: Overview

    in XboX Networking Hardware
    Ambit-Ubee: Overview: Ambit-Ubee (Modems/Gateways): Overview Ubee DDW3600 Login Information: Default Gateway - 192.168.100.1 / 192.168.0.1 Username – user / admin / root Password – user / cableroot / root...