Fritz!Box: Overview

Discus and support Fritz!Box: Overview in XboX Networking Hardware to solve the problem; Fritz!Box (Modems/Gateways): Overview Fritz!Box 7490 Login Information Gateway: Web Server's Default Page Username: admin Password: password... Discussion in 'XboX Networking Hardware' started by XBR Poseidon, Oct 9, 2014.

  1. XBR Poseidon
    XBR Poseidon Guest

    Fritz!Box: Overview


    Fritz!Box (Modems/Gateways): Overview
    Fritz!Box 7490

    Login Information



    *There have been reports that this device does not require a username and password*





    How to Find SSID (Network Name)

    (Network Name default is FRITZ!7272)

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select WLAN from the menu on the left.
    5. Select Radio Network from the resulting sub-menu.
    6. The wireless network name will be found to the right of Name of the WLAN radio network.
    How To Find Wireless Passphrase (WPA/WEP)

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select WLAN from the menu on the left.
    5. Select Security from the resulting sub-menu.
    6. The Wireless Passphrase can be found under the encryption tab.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select WLAN from the menu on the left.
    5. Select Security from the resulting sub-menu.
    6. Select non-encrypted on the Encryption tab.
    7. Click the Apply button.


    MAC Filtering

    Is available but exact instructions could not be found.

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Change the view to Advanced/Expert by clicking that option at the top of the screen.
    5. Select WLAN from the menu on the left.
    6. Select Radio Network from the resulting sub-menu.
    7. Choose Allow new WLAN devices.
    8. Click the Apply button at the bottom of the screen.


    Change Wireless Channel

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select WLAN from the menu on the left.
    5. Select Radio Channel from the resulting sub-menu.
    6. Select the desired channel. (Channels 1,3,9,11)
    7. Click the Apply button at the bottom of the screen.


    Change Wireless Mode

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select WLAN from the menu on the left.
    5. Select Radio Channel from the resulting sub-menu.
    6. Select 802.11g from the WLAN standard.
    7. Click the Apply button at the bottom of the screen.


    Change Wireless Band (Width)

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select WLAN from the menu on the left.
    5. Select Radio Channel from the resulting sub-menu.
    6. Select 802.11g from the WLAN standard.
    7. Click the Apply button at the bottom of the screen.


    DHCP Reservation

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Home Network from the menu on the left.
    5. Select Network from the resulting sub-menu.
    6. Click the Edit () button next to the device that you would like to always have the same IP Address.
    7. Enable the “Always assign this device the same IPv4 address”
    8. Click the Apply button at the bottom of the screen.


    UPnP

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Home Network from the menu on the left.
    5. Select Network from the resulting sub-menu.
    6. Select the UPnP tab at the top.
    7. Toggle UPnP on or of depending on your scenario.
    8. Click the Apply button at the bottom of the screen.


    DMZ

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Internet from the menu on the left.
    5. Select Permit Access from the resulting sub-menu.
    6. Select the Port Forwarding tab.
    7. Click the New Port Forwarding button.
    8. Select Exposed Host from the Port Forwarding Enabled for.
    9. Select your Xbox console.
    10. Click the OK button to save the changes.


    Disable DMZ

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Internet from the menu on the left.
    5. Select Permit Access from the resulting sub-menu.
    6. Select the Port Forwarding tab.
    7. Click the red X button next to the Exposed host entry.


    Port Forwarding

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Internet from the menu on the left.
    5. Select Permit Access from the resulting sub-menu.
    6. Click the New Port Forwarding button.
    7. Select Other Applications.
    8. Enter a name for the port forwarding rule. (Xbox Live)
    9. Set the Protocol to both TCP and UDP if it is available. If it is not two rules will need to be created, one TCP and the other UDP.
    10. Enter 3074 for both the port and to port.
    11. Select your Xbox console from the to computer drop down menu.
    12. Click OK to save your settings.
    13. Click the New Port Forwarding button.
    14. Select Other Applications.
    15. Enter a name for the port forwarding rule. (Xbox Live)
    16. Set the Protocol to UDP.
    17. Enter 3544 for both the port and to port.
    18. Select your Xbox console from the to computer drop down menu.
    19. Click OK to save your settings.


    Disable Port Forwarding

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Internet from the menu on the left.
    5. Select Permit Access from the resulting sub-menu.
    6. Click the Red X located to the right of any entries referring to Xbox.


    Firewall

    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Internet from the menu on the left.
    5. Select Filters from the resulting sub-menu.
    6. Click the Lists tab.
    7. Disable the Teredo-Filter aktiv option.
    8. Click the Apply button at the bottom of the screen.


    How to Find Firmware Version



    Firmware Update

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar.
    3. Press enter.
    4. Select System from the menu on the left.
    5. Select Update or Firmware Update from the resulting sub menu.
    6. If there is a new firmware version available there will be a Start Firmware Update Now button.
    Restore Factory Defaults

    From Hardware:

    1. Locate the back of the device, where the Ethernet port are located.
    2. Hold the reset button on the back for 30 seconds. You will need a paperclip, toothpick or pen to hold down the reset button.
    3. Let go of the reset button and wait about 1 minute for the device to reboot.


    From Firmware:



    1. Connect a computer to the gateway using and Ethernet cable.
    2. Disconnect the Fritz!Box from its power supply.
    3. Wait 5 seconds and reconnect the power.

      The Device can only be reset within 10 minutes of a reboot.
    4. Open a web browser.
    5. Navigate to Web Server's Default Page
    6. Click the Forgot your password link to default the device.


    Entering PPPoE



    1. Connect a computer to the gateway with an Ethernet cable.
    2. Open a web browser on a computer.
    3. Type the gateway address, Web Server's Default Page into the web address bar, hit enter.
    4. Select Advanced from the view menu at the top.
    5. Select Internet from the menu on the left.
    6. Select Account Information from the resulting sub-menu.
    7. Enter the PPPoE user name and password in the provided spaces.
    8. Click the Apply button found at the bottom of the screen.


    Known Issues

    There are no currently known issues with this device.



    Multiple console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.



    Device Manual

    The device manual can be found
    here
    . This manual is for the 7272 but the device interface is the same.

    :)
     
    XBR Poseidon, Oct 9, 2014
    #1
  2. XBR Poseidon
    XBR Poseidon Guest
    Fritz!Box: Overview

    Fritz!Box (Modems/Gateways): Overview
    Fritz!Box 7330

    Login Information:

    Default Gateway – Web Server's Default Page

    Username – there is no username or password unless one is set by the user.

    Password –

    How to Find SSID (Network Name)

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Radio Network from the sub-menu.
    5. The network name will be listed next to Network Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Security from the sub-menu.
    5. The Wireless passphrase can be found at the bottom of the page next to WLAN key.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Security from the sub-menu.
    5. Select non-encrypted if no security is desired.
    6. Click the Apply button to save these changes.


    MAC Filtering



    *Not available*



    Change Wireless Mode

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Radio Channel from the sub-menu.
    5. Select Adjust radio channel settings.
    6. From the drop down menu labeled WLAN Standard select 802.11b+g.
    7. Click the Apply button to save these changes.


    Change Wireless Channel

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Radio Channel from the sub-menu.
    5. Select Adjust Radio channel settings.
    6. Click the Apply button at the bottom of the screen.
    1. Select from the channel drop down the desired network channel. (Channels 1,3,9,11)


    DHCP Reservation

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select Advanced Settings.
    4. Select System from the sub-menu.
    5. Select Expert Mode.
    6. Enable the Show expert settings option.
    7. Click the Apply button.
    8. Select System.
    9. Select Network Settings.
    10. Click the IP Addresses button.
    11. Enter the IP Address and MAC Address of your Xbox console.
    12. Click the Apply button.


    UPnP

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Home Network".
    4. Click "Network" in the "Home Network" menu.
    5. Click the "Network Settings" tab.
    6. Enable the option "Transmit status information over UPnP".
    7. Click "Apply" to save your settings.
    8. Click "Permit Access" in the "Internet" menu.
    9. Click the "Port Forwarding" tab.
    10. Enable the option "Allow changes to security settings over UPnP".
    11. Click "Apply" to save your settings.


    DMZ

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Click the "Port Forwarding" tab.
    6. Click "New Port Forwarding".
    7. Select the "Exposed Host" entry from the drop-down menu "Port forwarding enabled for".
    8. Select the network device (for example a computer) for which you wish to enable port forwarding




    Disable DMZ

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Delete the entry for the Xbox console by clicking the red X to the right.


    Port Forwarding

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Click the "Port Forwarding" tab.
    6. Click "New Port Forwarding".
    7. Select "Other applications" from the "Port forwarding enabled for" list.
    8. Enter a name of your choice for the port forwarding rule in the "Name" field.
    9. Set the protocol to TCP from the "Protocol" drop-down menu.
    10. Enter 3074 for both the “From Port” and the “To Port”.
    11. Select your Xbox console from the “to computer” drop down.
    12. Click “Ok”.
    13. Click "New Port Forwarding".
    14. Select "Other applications" from the "Port forwarding enabled for" list.
    15. Enter a name of your choice for the port forwarding rule in the "Name" field.
    16. Set the protocol to UDP from the "Protocol" drop-down menu.
    17. Enter 3074 for both the “From Port” and the “To Port”.
    18. Select your Xbox console from the “to computer” drop down.
    19. Click “Ok”.




    Disable Port Forwarding

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Click the "Port Forwarding" tab.
    6. Click the red X to the right of the two rules that were created.


    Firewall

    *Not Available*



    Restoring Factory Defaults

    Through Firmware

    *This device is unique in that it resets via a command entered by handset.



    1. Pick up the handset.
    2. Dial # 991 * 15901590*
    3. The device will now restart with factory settings.


    How to Find Firmware Version

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click the Wizard button in the lower left.
    4. Click the Update Firmware link.
    5. Follow the on screen wizard to update the devices firmware if an update is available.


    Firmware Update



    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click the Wizard button in the lower left.
    4. Click the Update Firmware link.
    5. Follow the on screen wizard to update the devices firmware if an update is available.


    Bridging Guide

    *Bridge mode should only be used if you have a router to plug into the device.*

    *Not Available*



    Multiple Console Support

    We have no confirmed cases where multiple consoles were able to obtain an Open NAT state while using this device. Please comment on this page if you have been able obtain Open NAT on two or more consoles using this device.



    Known Issues



    Xbox One users are unable to play P2P multiplayer or party chat when connected Fritz!Box router that has an IPv6 address assigned by the ISP. Running tests via
    www.test-ipv6.com will help identify if an IPv6 address is present or viewing the WAN interface status in the router UI. Running the Test Multiplayer Connection troubleshooting tool on the console will
    indicate that a Teredo Address is not present.

    Disable IPv6 on the router to re-enable Teredo tunneling required for P2P multiplayer.

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select Internet from the menu on the left.
    4. Select Account Information from the sub-menu.
    5. Select the IPv6 tab from the top of the menu.
    6. Uncheck the IPv6 support check box.
    7. Click the Apply button.


    Device Manual

    Manual
     
    XBR Poseidon, Oct 9, 2014
    #2
  3. XBR Poseidon
    XBR Poseidon Guest
    Fritz!Box: Overview

    Fritz!Box (Modems/Gateways): Overview
    Fritz!Box 7360

    Login Information:

    Default Gateway – Web Server's Default Page

    Username – there is no username or password unless one is set by the user.

    Password –



    How to Find SSID (Network Name)

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Radio Network from the sub-menu.
    5. The network name will be listed next to Network Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Security from the sub-menu.
    5. The Wireless passphrase can be found at the bottom of the page next to WLAN key.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Security from the sub-menu.
    5. Select non-encrypted if no security is desired.
    6. Click the Apply button to save these changes.


    MAC Filtering



    *Not available*



    Change Wireless Mode

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Radio Channel from the sub-menu.
    5. Select Adjust radio channel settings.
    6. From the drop down menu labeled WLAN Standard select 802.11b+g.
    7. Click the Apply button to save these changes.


    Change Wireless Channel

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select WLAN from the menu on the left.
    4. Select Radio Channel from the sub-menu.
    5. Select Adjust Radio channel settings.
    6. Click the Apply button at the bottom of the screen.
    1. Select from the channel drop down the desired network channel. (Channels 1,3,9,11)


    DHCP Reservation

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select Advanced Settings.
    4. Select System from the sub-menu.
    5. Select Expert Mode.
    6. Enable the Show expert settings option.
    7. Click the Apply button.
    8. Select System.
    9. Select Network Settings.
    10. Click the IP Addresses button.
    11. Enter the IP Address and MAC Address of your Xbox console.
    12. Click the Apply button.


    UPnP

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Home Network".
    4. Click "Network" in the "Home Network" menu.
    5. Click the "Network Settings" tab.
    6. Enable the option "Transmit status information over UPnP".
    7. Click "Apply" to save your settings.
    8. Click "Permit Access" in the "Internet" menu.
    9. Click the "Port Forwarding" tab.
    10. Enable the option "Allow changes to security settings over UPnP".
    11. Click "Apply" to save your settings.


    DMZ

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Click the "Port Forwarding" tab.
    6. Click "New Port Forwarding".
    7. Select the "Exposed Host" entry from the drop-down menu "Port forwarding enabled for".
    8. Select the network device (for example a computer) for which you wish to enable port forwarding




    Disable DMZ

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Delete the entry for the Xbox console by clicking the red X to the right.


    Port Forwarding

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Click the "Port Forwarding" tab.
    6. Click "New Port Forwarding".
    7. Select "Other applications" from the "Port forwarding enabled for" list.
    8. Enter a name of your choice for the port forwarding rule in the "Name" field.
    9. Set the protocol to TCP from the "Protocol" drop-down menu.
    10. Enter 3074 for both the “From Port” and the “To Port”.
    11. Select your Xbox console from the “to computer” drop down.
    12. Click “Ok”.
    13. Click "New Port Forwarding".
    14. Select "Other applications" from the "Port forwarding enabled for" list.
    15. Enter a name of your choice for the port forwarding rule in the "Name" field.
    16. Set the protocol to UDP from the "Protocol" drop-down menu.
    17. Enter 3074 for both the “From Port” and the “To Port”.
    18. Select your Xbox console from the “to computer” drop down.
    19. Click “Ok”.




    Disable Port Forwarding

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click "Internet".
    4. Click "Permit Access" in the "Internet" menu.
    5. Click the "Port Forwarding" tab.
    6. Click the red X to the right of the two rules that were created.


    Firewall

    *Not Available*



    Restoring Factory Defaults

    Through Firmware

    *This device is unique in that it resets via a command entered by handset.



    1. Pick up the handset.
    2. Dial # 991 * 15901590*
    3. The device will now restart with factory settings.


    How to Find Firmware Version

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click the Wizard button in the lower left.
    4. Click the Update Firmware link.
    5. Follow the on screen wizard to update the devices firmware if an update is available.


    Firmware Update



    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Click the Wizard button in the lower left.
    4. Click the Update Firmware link.
    5. Follow the on screen wizard to update the devices firmware if an update is available.


    Bridging Guide

    *Bridge mode should only be used if you have a router to plug into the device.*

    *Not Available*



    Multiple Console Support

    We have no confirmed cases where multiple consoles were able to obtain an Open NAT state while using this device. Please comment on this page if you have been able obtain Open NAT on two or more consoles using this device.



    Known Issues



    Xbox One users are unable to play P2P multiplayer or party chat when connected Fritz!Box router that has an IPv6 address assigned by the ISP. Running tests via
    www.test-ipv6.com will help identify if an IPv6 address is present or viewing the WAN interface status in the router UI. Running the Test Multiplayer Connection troubleshooting tool on the console will
    indicate that a Teredo Address is not present.

    Disable IPv6 on the router to re-enable Teredo tunneling required for P2P multiplayer.

    1. Open a web browser.
    2. Enter Web Server's Default Page in the address bar. (Or click the link). A username and password is not needed by default. If one was created you will need to enter it here.
    3. Select Internet from the menu on the left.
    4. Select Account Information from the sub-menu.
    5. Select the IPv6 tab from the top of the menu.
    6. Uncheck the IPv6 support check box.
    7. Click the Apply button.


    Device Manual

    Manual
     
    XBR Poseidon, Oct 9, 2014
    #3
  4. SenTinaL Oz Win User

    Known Issues

    I have noticed there is a newer Firmware for the 7390 listed, but it is German ... would this be ok for an Australian Fritz?

    FRITZ.Box_Fon_WLAN_7390.AnnexB.84.06.00.image 24-Oct-2013 10:15 15M

    ". FRITZ.Box_Fon_WLAN_7390 image *" containing the update file in this directory

    the current firmware (system software) for Box Fon WLAN 7390th

    Caution: This firmware is only for FRITZ Box Fon WLAN 7390 suitable!

    Product: FRITZ Box Fon WLAN 7390!

    Version: FRITZ OS 6.00 (84.06.00)

    Language: German

    Release date: 28/10/2013
  5. XBF Brad A Win User

    Fritz BOx

    Hi there Trained,

    Thanks for reaching out. I'm sorry to hear about the issue with the network connectivity on the Xbox One X.

    I recommend to try Clearing the Mac addresses on the Xbox.

    Check out these articles: Network settings on Xbox Oneand
    I get an error message when I run the ‘Test network connection’ on Xbox One.

    Try this:

    • Select Settings on the Xbox
    • Select Network
    • Select Network Settings
    • Select Advance Settings
    • Alternate Mac address
    • Select Clear
    • Select Restart

    This step will restart the console. When it reboots, Select Network >Select Network Settings > Set up wireless network.

    Try this out and let us know the results.

    Thanks,

    Brad
  6. ian rush-47D8E064-17 Win User

    Additional Network Ports for Multiplayer Gaming: PORT 3544 NOT REPLYING.... TEREDO IP ADDRESS

    THIS FIXED THE PROBLEM ON MY ROUTER

    Disabling the Teredo filter in the FRITZ!Box
    1. Click "Internet" in the FRITZ!Box user interface.
    2. Click "Filters" in the "Internet" menu.
    3. Click on the "Lists" tab.
    4. Disable the option "Teredo filter enabled".
    5. Click "Apply" to save the settings.
  7. BobMcFly247 Win User

    Set static IP, Xbox changes IP right back. Thus preventing me from connecting.

    Additional information:

    DMZ is called "exposed host" in the Fritz Box.
  8. taidara Win User

    Can't play Destiny, NAT Strikt, can't connect to teredo ip HEEEEELP!!!

    Great stuff!

    Thanks to both of you, for sharing the information, in regard to the Fritz!Box.
Thema:

Fritz!Box: Overview

Loading...
  1. Fritz!Box: Overview - Similar Threads - Fritz Box Overview

  2. : Fritz!Box 6490 cable - UPnP not workling properly

    in XboX Networking Hardware
    : Fritz!Box 6490 cable - UPnP not workling properly: : Fritz!Box 6490 cable - UPnP not workling properly hm, i think its an isp or server problem not on your side. 6998055c-09f4-4299-ab97-efc998ca42a8
  3. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 7272 Login Information Gateway: Web Server's Default Page Username: admin Password: password How to Find SSID (Network Name) (Network...
  4. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 7390 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set by the user....
  5. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 7360 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set by the user....
  6. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 7330 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set by the user....
  7. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 3390 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set by the user....
  8. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 3370 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set by the user....
  9. Fritz!Box FRITZ!Box 3272: Overview

    in XboX Networking Hardware
    Fritz!Box FRITZ!Box 3272: Overview: Fritz!Box (Modems/Gateways) FRITZ!Box 3272: Overview Fritz!Box 3272 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set...
  10. Fritz!Box: Overview

    in XboX Networking Hardware
    Fritz!Box: Overview: Fritz!Box (Modems/Gateways): Overview Fritz!Box 7360 Login Information: Default Gateway – Web Server's Default Page Username – there is no username or password unless one is set by the user....