Netgear Netgear DGN1000/DGN1000SP: Overview

Discus and support Netgear Netgear DGN1000/DGN1000SP: Overview in XboX Networking Hardware to solve the problem; Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Overview Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password -... Discussion in 'XboX Networking Hardware' started by XB1R Hades, Jul 11, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear Netgear DGN1000/DGN1000SP: Overview


    Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Overview
    Netgear DGN1000

    Login Information

    • Gateway - 192.168.0.1
    • Username - admin
    • Password - password

    How to Find SSID (Network Name)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The Network name will be listed as Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. Under Security Options select Disable.
    5. Select Apply.


    MAC Filtering

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. Under advanced select Wireless Settings.
    6. Select Setup Access List To access MAC Filtering.
    7. Uncheck Turn Access Control On
    8. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).
    7. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 54Mbps".
    7. Click Apply.




    DHCP Reservation

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin"/password.
    3. Click LAN Setup on the left.
    4. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    5. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
      click "Add" to finished the process.


    UPnP

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section choose UPnP.
    4. Toggle UPnP.


    DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Check the box next to Default DMZ Server.
    5. Enter the IP address assigned to the Xbox console you wish to DMZ.


    Disable DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Uncheck the box next to Default DMZ Server.
    5. Select apply.


    Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Click the Add Custom Service button at the bottom.
    6. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
      to port forward has.
    7. Click Apply.


    Disable Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Select the radio button for any rules needed to be removed.
    6. Select Delete Service.
    7. Select apply.


    Firewall

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    3. From the menu on the left select WAN Setup.
    4. Check the Disable SPI Firewall box.
    5. Change NAT Filtering from secured to Open.


    How to Find Firmware Version



    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administration from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
      finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.




    Entering PPPoE

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. the default user name and password are: "admin", "password".
    4. From the left hand menu select Basic Settings.
    5. Where it says Does your internet connection require a login select yes.
    6. Enter the user name and password for your pppoe in their respective fields.
    7. Select apply.




    Known Issues

    There are no known issues with this device.

    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.

    :)
     
    XB1R Hades, Jul 11, 2014
    #1
  2. XB1R Hades
    XB1R Hades Guest
    Netgear Netgear DGN1000/DGN1000SP: Known Issues

    Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Known Issues
    Netgear DGN1000

    Login Information

    • Gateway - 192.168.0.1
    • Username - admin
    • Password - password
    Known Issues

    There are no known issues with this device.
     
    XB1R Hades, Jul 11, 2014
    #2
  3. XB1R Athena
    XB1R Athena Guest
    Netgear Netgear DGN1000/DGN1000SP: Device Manual

    Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Device Manual
    Device Manual

    Click
    here
    to go to a manual for this device
     
    XB1R Athena, Jul 11, 2014
    #3
  4. AlbertMc94 Win User

    system update failed

    its a netgear router the model number is: N150 wireless router modem DGN1000
  5. GMAN990 Win User

    netgear DGN1000 settings

    Hi,

    When you run the Xbox live connection test does it complain about NAT or not? Are you wireless if so which adapter are you using?
  6. DannyTx Win User

    Netgear: Overview

    I can't seem to get my nat type to open even after all these steps and the steps xbox provides for "cant find teredo IP" when i run multiplayer test I get that, and when i check more details it says im behind a firewall or not connected. I made sure i disabled
    SIP ALG and changed nat to open, and still doesnt work.
  7. queenquim2005 Win User

    Connection problems

  8. XBF Leonzo G Win User

    Netgear Netgear DGN1000/DGN1000SP: Microsoft store says check your connection looks your offline microsoft store needs comnection

    Hello Rfbgdgg!

    Thank you very much for bringing this issue to our attention. What type of error message are you seeing when testing the network and multiplayer connection on the Xbox One? If we need to provide steps on how to test the connections please let us know. The
    most common solutions for any networking issues will be in this article
    I get an error message when I run the ‘Test network connection’ on Xbox One
    . Be sure to let us know the results!
Thema:

Netgear Netgear DGN1000/DGN1000SP: Overview

Loading...
  1. Netgear Netgear DGN1000/DGN1000SP: Overview - Similar Threads - Netgear Netgear DGN1000

  2. Netgear Netgear DGN1000/DGN1000SP: Microsoft store says check your connection looks your ...

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Microsoft store says check your connection looks your ...: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Microsoft store says check your connection looks your offline microsoft store needs comnection Hello Rfbgdgg! Thank you very much for bringing...
  3. Netgear Netgear DGN1000/DGN1000SP: Known Issues

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Known Issues: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Known Issues Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password Known Issues There are no...
  4. Netgear Netgear DGN1000/DGN1000SP: Entering PPPoE

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Entering PPPoE: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Entering PPPoE Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password Entering PPPoE Plug the...
  5. Netgear Netgear DGN1000/DGN1000SP: Restore Factory Defaults

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Restore Factory Defaults: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Restore Factory Defaults Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password Restore Factory...
  6. Netgear Netgear DGN1000/DGN1000SP: Firmware Update

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Firmware Update: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Firmware Update Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password Firmware Update Auto...
  7. Netgear Netgear DGN1000/DGN1000SP: How to Find Firmware Version

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: How to Find Firmware Version: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: How to Find Firmware Version Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password How to Find...
  8. Netgear Netgear DGN1000/DGN1000SP: Firewall

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Firewall: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Firewall Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password Firewall Login to router by...
  9. Netgear Netgear DGN1000/DGN1000SP: Port Forwarding

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Port Forwarding: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Port Forwarding Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password Port Forwarding Login to...
  10. Netgear Netgear DGN1000/DGN1000SP: DMZ

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: DMZ: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: DMZ Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password DMZ Login to router by entering...