Netgear: Overview

Discus and support Netgear: Overview in XboX Networking Hardware to solve the problem; Netgear (Routers): Overview Netgear JNR3210 Login Information Gateway - 192.168.1.1, 10.0.0.1, or http://routerlogin.net Username - admin Password... Discussion in 'XboX Networking Hardware' started by XB1R Hades, Apr 27, 2014.

  1. XB1R Hades
    XB1R Hades Guest

    Netgear: Overview


    Netgear (Routers): Overview
    Netgear JNR3210

    Login Information


    Netgear Smart Wizard - Light Blue

    How to Find SSID (Network Name)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The Network name will be listed as Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. Under Security Options select Disable.
    5. Select Apply


    Change Wireless Channel

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).
    7. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 54Mbps".
    7. Click Apply.
    Change Wireless Band (Width)



    The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set
    the wireless band to 20MHz only, follow these steps.



    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering Router login in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 217Mbps" or lower.
    7. Select Apply.




    MAC Filtering

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. Under advanced select Wireless Settings.
    6. Select Setup Access List To access MAC Filtering.
    7. Uncheck Turn Access Control On
    8. Select Apply.


    DHCP Reservation

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin"/password.
    3. Click LAN Setup on the left.
    4. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    5. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
      click "Add" to finish the process.


    UPnP

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section choose UPnP.
    4. Toggle UPnP.


    DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Check the box next to Default DMZ Server.
    5. Enter the IP address assigned to the Xbox console you wish to DMZ.


    Disable DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Uncheck the box next to Default DMZ Server.
    5. Select apply.

    Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Click the Add Custom Service button at the bottom.
    6. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
      to port forward has.
    7. Click Apply.


    Disable Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Select the radio button for any rules needed to be removed.
    6. Select Delete Service.
    7. Select apply.

    Firewall

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    3. From the menu on the left select WAN Setup.
    4. Check the Disable SPI Firewall box.
    5. Change NAT filtering from secured to Open.


    How to Find Firmware Version

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. The Netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administraion from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, un-compress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
      finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    *There is no physical reset button on this device as far as we can tell. Please consult your user manual or Netgear support for information on how to perform a factory reset via the hardware.

    Entering PPPoE

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password. The default user name and password are: "admin", "password".
    4. From the left hand menu select Basic Settings.
    5. Where it says Does your internet connection require a login select yes.
    6. Enter the user name and password for your PPPoE in their respective fields.
    7. Select apply.


    Netgear Genie - Black/Purple

    How to Find SSID (Network Name)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      The default user name and password are: "admin", "password".
    3. Select Basic from the menu on the top.
    4. Select Wireless from the left menu.
    5. Your network name will be listed as Name(SSID).



    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. Under Security Options select the desired security type.
    6. Select Apply.


    MAC Filtering

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select Advanced from the menu on the left.
    4. Under Advanced select Wireless Settings.
    5. Select Setup Access List To access MAC Filtering.
    6. Uncheck Turn Access Control On
    7. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open a web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select Wireless settings from the left hand menu under Setup.
    8. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)
    9. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 54Mbps".
    8. Click Apply.
    Change Wireless Band (Width)



    The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set
    the wireless band to 20MHz only, follow these steps.



    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering Router login in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 217Mbps" or lower.
    8. Select Apply.




    DHCP Reservation

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin"/password.
    3. Select Advanced from the tabs at the top.
    4. Click Setup from the menu on the left.
    5. Click Lan Setup in the submenu that appears.
    6. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    7. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then
      click "Add" to finish the process.


    UPnP

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu choose UPnP.
    6. Toggle UPnP.


    DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Check the box next to Default DMZ Server if it is not.
    7. Enter the IP address assigned to the Xbox console you wish to DMZ
    8. Select Apply.


    Disable DMZ

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Uncheck the Default DMZ Server
    7. Select Apply.


    Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Click the Add Custom Service button at the bottom.
    8. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish
      to port forward has.
    9. Click apply.


    Disable Port Forwarding

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Select the service you want to delete from the radio button on the left.
    8. Select Delete Service.

    Firewall

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Setup from the menu on the left.
    5. From the submenu select WAN Setup.
    6. Check the Disable SPI Firewall box.
    7. Change NAT Filtering from secured to Open.


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    *There is no physical reset button on this device as far as we can tell. Please consult your user manual or Netgear support for information on how to perform a factory reset via the hardware.



    How to Find Firmware Version

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Administration from the menu on the left.
    5. Select Router Status under administration.
    6. The Firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. The Netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an Ethernet cable.
    2. Open web browser.
    3. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select administration from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, un-compress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router
      finishes restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed.


    Entering PPPoE

    1. Login to router by entering http://routerlogin.net in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    3. Select the Basic tab from the tabs at the top.
    4. Select Internet from the menu on the left
    5. Where it asks if your internet connection requires a login select yes.
    6. Input in your PPPOE user name and password.
    7. Select Apply.



    Known Issues

    There are no known issues with this device.



    Multiple Console Support

    We have no confirmed cases where multiple consoles were able to obtain an Open NAT state while using this device. Please comment on this page if you have been able obtain Open NAT on two or more consoles using this device.

    :)
     
    XB1R Hades, Apr 27, 2014
    #1
  2. XB1R Apollo
    XB1R Apollo Guest
    Netgear: Overview

    Netgear (Routers): Overview
    Netgear WNDR3700

    Login Information

    Netgear Smart Wizard - Light Blue

    How to Find SSID (Network Name)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The Network name will be listed as Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. Under Security Options select Disable.
    5. Select Apply


    MAC Filtering

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Under advanced select Wireless Settings.
    6. Select Setup Access List To access MAC Filtering.
    7. Uncheck Turn Access Control On
    8. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).
    7. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 54Mbps".
    7. Click Apply.
    Change Wireless Band (Width)

    The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set the wireless
    band to 20MHz only, follow these steps.

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering Router login in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 130Mbps" or lower.
    7. Select Apply.



    DHCP Reservation

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin"/password.
    3. Click LAN Setup on the left.
    4. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    5. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
      "Add" to finished the process.


    UPnP

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section choose UPnP.
    4. Toggle UPnP.


    DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Check the box next to Default DMZ Server.
    5. Enter the IP address assigned to the Xbox console you wish to DMZ.


    Disable DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Uncheck the box next to Default DMZ Server.
    5. Select apply.

    Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Click the Add Custom Service button at the bottom.
    6. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
      port forward has.
    7. Click Apply.


    Disable Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Select the radio button for any rules needed to be removed.
    6. Select Delete Service.
    7. Select apply.

    Firewall

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left select WAN Setup.
    4. Check the Disable SPI Firewall box.
    5. Change NAT Filtering from secured to Open.


    How to Find Firmware Version

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administraion from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.

    Entering PPPoE

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Basic Settings.
    5. Where it says Does your internet connection require a login select yes.
    6. Enter the user name and password for your pppoe in their respective fields.
    7. Select apply.


    Netgear Genie - Black/Purple

    How to Find SSID (Network Name)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Basic from the menu on the top.
    4. Select Wireless from the left menu.
    5. Your network name will be listed as Name(SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. Under Security Options select the desired security type.
    6. Select Apply.


    MAC Filtering

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Advanced from the menu on the left.
    4. Under Advanced select Wireless Settings.
    5. Select Setup Access List To access MAC Filtering.
    6. Uncheck Turn Access Control On
    7. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open a web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select Wireless settings from the left hand menu under Setup.
    8. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)
    9. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 54Mbps".
    8. Click Apply.
    Change Wireless Band (Width)

    The possibility of using 20MHz or 40MHz on this device is based on the current mode selected. If the devices' mode is set to "Up to 300Mbps" the channel width will likely switch between 20MHz and 40MHz depending on surrounding interference. To set the wireless
    band to 20MHz only, follow these steps.

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering Router login in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password. The default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 130Mbps" or lower.
    8. Select Apply.



    DHCP Reservation

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin"/password.
    3. Select Advanced from the tabs at the top.
    4. Click Setup from the menu on the left.
    5. Click Lan Setup in the submenu that appears.
    6. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    7. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
      "Add" to finished the process.


    UPnP

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu choose UPnP.
    6. Toggle UPnP.


    DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Check the box next to Defualt DMZ Server if it is not.
    7. Enter the IP address assigned to the Xbox console you wish to DMZ
    8. Select Apply.



    Disable DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Uncheck the Default DMZ Server
    7. Select Apply.


    Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Click the Add Custom Service button at the bottom.
    8. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
      port forward has.
    9. Click apply.


    Disable Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Select the service you want to delete from the radio button on the left.
    8. Select Delete Service.


    Firewall

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Setup setup from the menu on the left.
    5. From the submenu select WAN Setup.
    6. Check the Disable SPI Firewall box.
    7. Change NAT Filtering from secured to Open.


    How to Find Firmware Version

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Administration from the menu on the left.
    5. Select Router Status under administration.
    6. The Firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select administration from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed.


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.


    Entering PPPoE

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Basic tab from the tabs at the top.
    4. Select Internet from the the menu on the left
    5. Where it asks if your internet connection requires a login select yes.
    6. Input in your PPPOE user name and password.
    7. Select Apply.


    Device Manual

    WNDR3700v1

    WNDR3700v2

    WNDR3700v3

    WNDR3700v4



    Known Issues

    This device has no known issues.



    Multiple Console Support

    We have confirmed cases where this devices is able to support two or more consoles with Open NAT on this device.
     
    XB1R Apollo, Apr 27, 2014
    #2
  3. XB1R Athena
    XB1R Athena Guest
    Netgear: Overview

    Netgear (Routers): Overview
    Netgear WNR3500

    Login Information

    • Gateway - 192.168.1.1, 10.0.0.1, or routerlogin.net
    • Username - admin
    • Password – password

    Netgear Smart Wizard - Light Blue

    How to Find SSID (Network Name)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The Network name will be listed as Name (SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the Setup section choose Wireless Settings.
    4. Under Security Options select Disable.
    5. Select Apply


    MAC Filtering

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Under advanced select Wireless Settings.
    6. Select Setup Access List To access MAC Filtering.
    7. Uncheck Turn Access Control On
    8. Select Apply.


    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11).
    7. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    5. Select Wireless settings from the left hand menu under Setup.
    6. Select from the mode drop down "Up to 54Mbps".
    7. Click Apply.
    Change Wireless Band (Width)

    This router only supports the 20MHz band.



    DHCP Reservation

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin"/password.
    3. Click LAN Setup on the left.
    4. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    5. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
      "Add" to finished the process.


    UPnP

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section choose UPnP.
    4. Toggle UPnP.


    DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Check the box next to Default DMZ Server.
    5. Enter the IP address assigned to the Xbox console you wish to DMZ.


    Disable DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password the default user name and password are: "admin", "password".
    3. From the menu on the left under the advanced section select WAN Setup.
    4. Uncheck the box next to Default DMZ Server.
    5. Select apply.


    Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Click the Add Custom Service button at the bottom.
    6. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
      port forward has.
    7. Click Apply.


    Disable Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left select Port Forwarding/Port Triggering.
    4. Select the Port Forwarding button at the top of the main screen.
    5. Select the radio button for any rules needed to be removed.
    6. Select Delete Service.
    7. Select apply.


    Firewall

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    3. From the menu on the left select WAN Setup.
    4. Check the Disable SPI Firewall box.
    5. Change NAT Filtering from secured to Open.


    How to Find Firmware Version

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Administration from the menu on the left.
    5. Select Router Status under administration.
    6. The Firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select Administraion from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Backup Settings.
    5. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.


    Entering PPPoE

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Basic Settings.
    5. Where it says Does your internet connection require a login select yes.
    6. Enter the user name and password for your pppoe in their respective fields.
    7. Select apply.


    Netgear Genie - Black/Purple

    How to Find SSID (Network Name)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Basic from the menu on the top.
    4. Select Wireless from the left menu.
    5. Your network name will be listed as Name(SSID).


    How To Find Wireless Passphrase (WPA/WEP)

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. The wireless passphrase can be found near the bottom of the page.


    Changing Wireless Security Type/ Disabling Wireless Security

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Basic from the tabs at the top.
    4. From the menu on the left under the Setup section choose Wireless Settings
    5. Under Security Options select the desired security type.
    6. Select Apply.


    MAC Filtering

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Advanced from the menu on the left.
    4. Under Advanced select Wireless Settings.
    5. Select Setup Access List To access MAC Filtering.
    6. Uncheck Turn Access Control On
    7. Select Apply.
    Change Wireless Channel

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open a web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select Wireless settings from the left hand menu under Setup.
    8. From the drop down menu labeled Channel select the desired channel. (Channels 1,3,9,11)
    9. Click Apply.


    Change Wireless Mode

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. Select Basic from the tabs at the top.
    6. Select Wireless from the left hand menu.
    7. Select from the mode drop down "Up to 54Mbps".
    8. Click Apply.


    DHCP Reservation

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin"/password.
    3. Select Advanced from the tabs at the top.
    4. Click Setup from the menu on the left.
    5. Click Lan Setup in the submenu that appears.
    6. At the bottom of the page you will find the "Address Reservation" section. Click on "Add" to bring up a new menu.
    7. In this menu, if the Xbox you want to add is already on the network, you can select it by clicking on the radio button next to the device. This will populate the fields with the information, alternatively you can enter the information manually then click
      "Add" to finished the process.
    UPnP

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu choose UPnP.
    6. Toggle UPnP.
    DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Check the box next to Default DMZ Server if it is not.
    7. Enter the IP address assigned to the Xbox console you wish to DMZ
    8. Select Apply.



    Disable DMZ

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select Advanced from the tabs at the top.
    4. Select Setup.
    5. Select WAN Setup from the submenu.
    6. Uncheck the Default DMZ Server
    7. Select Apply.


    Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Click the Add Custom Service button at the bottom.
    8. In the following Screen enter a service name that indicates something to do with Xbox Live (XBL). Set the service type to both TCP and UDP. Set both the starting port and ending port to 3074. Then enter the IP address that the Xbox console you wish to
      port forward has.
    9. Click apply.
    Disable Port Forwarding

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Advanced setup from the menu on the left.
    5. From the submenu select Port Forwarding/Port Triggering.
    6. Select the Port Forwarding button at the top of the main screen.
    7. Select the service you want to delete from the radio button on the left.
    8. Select Delete Service.

    Firewall

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Advanced tab from the tabs at the top.
    4. Select Setup setup from the menu on the left.
    5. From the submenu select WAN Setup.
    6. Check the Disable SPI Firewall box.
    7. Change NAT Filtering from secured to Open.


    How to Find Firmware Version

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the user name and password.the default user name and password are: "admin", "password".
    4. From the left hand menu select Router Status.
    5. The firmware version will be listed as Firmware Version.


    Firmware Update

    Auto Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. The netgear smart wizard will automatically search for updates upon login, if an update is available click install.
    Manual Update

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Open web browser.
    3. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    4. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    5. Select Advanced from the tabs at the top.
    6. Select administration from the menu on the left.
    7. Select Router Update from the submenu.
    8. In an alternate web browser or tab go to www.NETGEAR.com and download the updated software. If not done automatically, uncompress the file.
    9. Click Browse.
    10. Locate and select the file you just downloaded and uncompressed.
    11. Click Upload to send the software to the router. This loads the new software in the router and causes the router to restart. Note: Do not try to go online, turn off the router, shutdown the computer or do anything else to the router until the router finishes
      restarting! When the Ready light stops blinking, wait a few more seconds before doing anything.
    12. Click Router Status and check the Firmware Version to verify that your router now has the new software installed.


    Restore Factory Defaults

    Through firmware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    3. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    4. Select the Advanced tab from the tabs at the top.
    5. Select Administration from menu on the left.
    6. From the submenu select Backup Settings.
    7. Select the Erase option under where it says Revert to factory default settings.
    Through Hardware

    1. Plug the computer into a LAN port via an ethernet cable.
    2. Locate the reset button on the device.
    3. With paperclip/pen/toothpick hold down the reset button down for 30 seconds.
    4. Wait for lights to turn off then return to normal.



    Entering PPPoE

    1. Login to router by entering
      http://routerlogin.net
      in to the address bar or by entering the default gateway IP address.
    2. The router will then prompt you to enter the username and password.

      the default user name and password are: "admin", "password".
    3. Select the Basic tab from the tabs at the top.
    4. Select Internet from the the menu on the left
    5. Where it asks if your internet connection requires a login select yes.
    6. Input in your PPPOE user name and password.
    7. Select Apply.


    Multiple Console Support

    We have confirmed that this network device is unable to support more than one console with an Open NAT.

    Device Manual

    WNR3500

    WNR3500v2

    Known Issues

    There are no known issues with this device.
     
    XB1R Athena, Apr 27, 2014
    #3
  4. DannyTx Win User

    Netgear: Overview

    I can't seem to get my nat type to open even after all these steps and the steps xbox provides for "cant find teredo IP" when i run multiplayer test I get that, and when i check more details it says im behind a firewall or not connected. I made sure i disabled
    SIP ALG and changed nat to open, and still doesnt work.
  5. Mister Ohnaka Win User

    MTU Error; no internet connection after move

    Hello Jr,

    Sorry to hear about the connection troubles. Let's see if we can get this working for you.

    Are you able to connect directly to your modem via an ethernet cable? This will help us narrow it down. Also, here is an overview of your router if needed for further troubleshooting: Netgear
    WNR3500
    .

    Let us know how that direct connection works, and we can go from there.
  6. SnakyToast2841 Win User

    Overview

    Clear your system Cache by holding the power button for 15 seconds, then unplug your Xbox One for 1 minute, after forwarding ports 53,80,88,500,3074,3544,4500.
  7. cookieater821 Win User

    Overview

    BRIDGE mode is under LAN setting routed with NAT and routed without NAT or select BRDIGE MODE. Don't forget to click APPLY then power cycle gateway -
  8. mermaidbythesea-A337 Win User

    Overview

    [quote user="XB1R Athena"]

    Internet service type: 3G/4G



    Common devices:

    Sierra Wireless: Overdrive Pro

    Sierra Aircard: 250U



    ISP Website: http://sprint.com



    Support number: 1-888-211-4727

    [/quote]
Thema:

Netgear: Overview

Loading...
  1. Netgear: Overview - Similar Threads - Netgear Overview

  2. Netgear DGN3500: Netgear LB2120 UPnP Unavailable

    in XboX Networking Hardware
    Netgear DGN3500: Netgear LB2120 UPnP Unavailable: Netgear DGN3500: Netgear LB2120 UPnP Unavailable I'm a bit confused about what you mean by "this device is linked to an actual router". From the specifications, the LB2120 takes a wired WAN...
  3. Netgear DGND3700: Netgear C3700-N600 Disconnecting from Xbox 360 Live

    in XboX Networking Hardware
    Netgear DGND3700: Netgear C3700-N600 Disconnecting from Xbox 360 Live: Netgear DGND3700: Netgear C3700-N600 Disconnecting from Xbox 360 Live XBF Leo G, It kicks me off of Xbox 360 Live, NOT the network. I am still connected to the network, but have to reconnect to...
  4. : My XBox can't connect to Netgear Orbi WIFI

    in XboX Networking Hardware
    : My XBox can't connect to Netgear Orbi WIFI: : My XBox can't connect to Netgear Orbi WIFI Hi Sluzze, Thanks for keeping us updated with your replies. Sorry to hear you're still experiencing the same issue. Since you received the error...
  5. Netgear D7000v2 24/7 Strict Nat

    in XBoX Games and Apps
    Netgear D7000v2 24/7 Strict Nat: I have never had an open nat. I've tried numerous thungs .UPNP, Port Forwarding, Static IP, Port Triggering, Updating router and the list extends 99% of the time it says UPNP failed .Other times...
  6. Netgear Netgear DGN3500: Overview

    in XboX Networking Hardware
    Netgear Netgear DGN3500: Overview: Netgear (Modems/Gateways) Netgear DGN3500: Overview Netgear DGN3500 Login Information Gateway - 192.168.0.1 Username - admin Password - password How to Find SSID (Network Name) Login to...
  7. Netgear Netgear DGN2200: Overview

    in XboX Networking Hardware
    Netgear Netgear DGN2200: Overview: Netgear (Modems/Gateways) Netgear DGN2200: Overview Netgear DGN2200 Login Information Gateway - 192.168.0.1 Username - admin Password - password Netgear SmartWizard How to Find SSID...
  8. Netgear Netgear DGN1000/DGN1000SP: Overview

    in XboX Networking Hardware
    Netgear Netgear DGN1000/DGN1000SP: Overview: Netgear (Modems/Gateways) Netgear DGN1000/DGN1000SP: Overview Netgear DGN1000 Login Information Gateway - 192.168.0.1 Username - admin Password - password How to Find SSID (Network Name)...
  9. Netgear Netgear CG3100D: Overview

    in XboX Networking Hardware
    Netgear Netgear CG3100D: Overview: Netgear (Modems/Gateways) Netgear CG3100D: Overview Netgear CG3100D Login Information: Default Gateway - 192.168.0.1 Username – admin Password – password How to Find SSID (Network Name)...
  10. Netgear Netgear DGND3700: Overview

    in XboX Networking Hardware
    Netgear Netgear DGND3700: Overview: Netgear (Modems/Gateways) Netgear DGND3700: Overview Netgear DGND3700 Login Information: Default Gateway - 192.168.0.1 Username – admin Password – password How to Find SSID (Network...